2017+ Honda Civic EDFC Install

With the release of the current body style Civic FLEX Z Coilovers, we have been receiving more and more inquiries of how the EDFC Motors would mount, specifically the rears due to its limited accessibility. Luckily a close friend of ours was interested in the EDFC Active for his vehicle so I went ahead and did the install for him.

Since I had never really had a chance to look over the vehicle you can say I went into this blindly. Initially accessing power for the EDFC Active controller and driver units seemed to be impossible (at least in the engine compartment area) without requiring modifictions. I basically just wired up all three to the main fuse box under the dash. Also for reference, the Driver Unit power cables are be able to reach the main fuse box under the dash, the rear being longer and front slightly shorter in length. I was under the impression that they were the same length. The front Driver Unit was installed next to the Engine Compartment Fuse Box and the rear was placed on the backside rear bulkhead. Both were in decent areas for placement. However it’s eventually up to you on the placement for the driver units. Just make sure the heat sink portion of the driver unit has enough space to dissipate heat. Power source was setup first as I wanted to avoid staining any of the interior, since the rears required the shocks to be removed.

Engine Compartment Driver Mount
Rear Bulkhead Driver Unit Mount

Installation of the front for this Civic required the use of the EDFC Motor Extension Kit to relocate the motors. Although it looks like the EDFC Motor will clear the hood, it in fact does not. The Click Assembly is first removed with the Hex Bolt. Once removed I applied the supplied grease to the hex bolt hole, wiping any excess grease from the piston shaft.

Next a small amount of Thread Locker (also included with the EDFC Motor Kit) is lightly applied to the piston shaft outer thread on both sides (where the Extension Kit’s Top Adapter screws on to).

Then the Top Adapter base is tightened onto the shaft using a 19mm wrench. Please note that a very minimal amount of force was exerted to the Top Adapter and should not be overtightened as it can break. Next the gold adjusting rod (Conversion Rod) is installed in the Top Adapter hole.

Prior to installing the 90 degree angle (Cover) and clip to the Top Adapter, I installed the Extension adding threadlocker on it and hand tightened it. Make sure that the Inner Shaft is turned out as to avoid any hangups with it against the gold Conversion Rod when installing.

Then proceed to install them on to the Top Adapter pressing down firmly to also press down the gold Conversion Rod and allow you to insert the locking clip to lock against the base. Afterwards add threadlocker to the other end of the Extension and proceed to install the EDFC Motor and also hand tightened it. Motor mounting location is up to you as some may have different locations preferred then the ones I had chosen. Also, do not bend the Extension (no U bends). It only allows a minimal amount of bending.

The fronts were not too bad to install. However, the rears were another story. Since only TEIN Japan had a chance to do an EDFC installation noting down key areas in the rear shock’s mounting tower where the EDFC motor cable is to exit, this gave us an opportunity to see if this would be the same for U.S. market applications. The wheelwell liner should be removed before uninstalling anything as it allows for a clear view of the shock mount tower area.

Due to limited accessibilty of the lower shock bolt, the rear spring should also be removed. Once the shock is removed the upper mount also needed to be disassembled to allow removal of the click assembly.

Once the click is removed apply the grease into the hex bolt hole then (applicable to EDFC ACTIVE and ACTIVE PRO models) install the supplied gold color hex bolt flush with the top of the piston rod. Reinstall the mount back on the damper. Apply grease to the hex bolt, then apply threadlocker to the piston shaft threads.

Proceed to install the EDFC motor hand tight to the threaded piston rod. Now, check that the EDFC Motor’s shaft turns freely by using a flathead screwdriver to turn the shaft- you should be able to complete several turns in either direction (it should eventually stop in either direction). The EDFC Motor cover was a slight pain to install since accessibility of the motor inside the cup-shaped upper mount was extremely limited. On a side note, I have seen where the Motor cover was preinstalled and a slit cut on the top of the EDFC Motor allowing for screwdriver access to the Motor’s shaft. Then once you check for free movement of the shaft, the slit can be resealed with silicon. Either method of EDFC Motor install works.

Prior to reinstalling shock, the EDFC Mid-Cable would need to be installed. As you can see in the images, there is a small access hole next to the main tower hole where the shock would mount.

The male connector of the mid cable needs to be fed through the smaller access hole over to the shock hole. Please take note that the cable connector also needs to be pushed through a small clearance on the top upper corner of the smaller access hole (as shown in the noted image).

Once pushed through, position the shock on its mount (I recommend to install the bolt through the lower shock eye ring bushing for support.) then connect the two cables together and gently pull the mid cable and EDFC motor cable through. During this time you would also need to move the shock’s upper mount closer to the tower to avoid tearing the cable wire. Once the shock mount is close enough, a bolt can be threaded on to hold the upper mount in place allowing for the cable slack to be removed then the mount to be completely reinstalled. Afterwards you can reinstall the shock bolt and spring, applying suspension preload when tightening up the loosened bolts.The EDFC Mid Cables were ran through existing grommets into the trunk area to the driver unit.

Though this install took a little longer than anticipated, we have a better understanding for installing EDFC ACTIVE (and EDFC ACTIVE PRO) on 2017+ Honda Civic models. Hope this helps out for any out there looking to install our EDFC systems on similar applications. As per usual you can alway contact us direct should you have any technical questions.

Tokyo Auto Salon 2016

We sent a couple of TEIN USA staff to Japan to attend the Tokyo Auto Salon car show at Makuhari Messe, as well as to assist and represent the North American market.

TAS 2016 (iPad Pictures) 027 blog

The TEIN group has been active in Tokyo Auto Salon for many years now. Each and every year is a perfect time to showcase our latest technologies and product releases directly to the consumer.

Unlike shows like the SEMA Show in Las Vegas, Nevada, Tokyo Auto Salon allows consumers (potential customers) to see what’s new, and to also speak directly with the manufacturer. That’s great since there’s not really any salesperson trying to breathe down their necks and push products on them. The customer has the freedom to choose WHAT THEY LIKE!

The turnout was good- just over 144,000 visitors during the 3-day event. We had a total of just 14,000 visitors to the TEIN booth alone. So for sure we kept very busy. I personally felt bad since my Japanese speaking skills are next to nil. However, I met several Westerners, and even some TEIN USA dealers! That was nice! Better than standing quiet the whole weekend, hahaha!!!

On top of our displays, we had goods for sale, a “Garapon” raffle, and a real-life Dampachi and Dampatty that visitors could take photos with!

Tokyo Auto Salon (Jan 17, 2016) 075 blog Tokyo Auto Salon (Jan 17, 2016) 052 blog Tokyo Auto Salon (Jan 17, 2016) 058 blog Tokyo Auto Salon (Jan 17, 2016) 048 blog Tokyo Auto Salon (Jan 17, 2016) 080 blog Tokyo Auto Salon (Jan 17, 2016) 097 blog

Speaking of our “Garapon” raffle, we had a few big winners:

Tokyo Auto Salon (Jan 17, 2016) 067 blog

This visitor got the grand prize- a damping adjustable TEIN suspension of his choice + an EDFC ACTIVE PRO setup!

Tokyo Auto Salon (Jan 17, 2016) 050 blog

This was our second big winner. He wins a TEIN suspension kit of his choice!

Tokyo Auto Salon (Jan 17, 2016) 046 blog

This winner gets a free set of TEIN lowering springs!

Other prizes ranged from TEIN original goods and stickers, to calendars and posters. So there was something for everyone that played!

As for new products, TEIN Japan brought out the upcoming STREET SPORTS line of premium shock absorbers. A perfect match for our S.TECH and HIGH TECH line of lowering springs, or as a great upgrade replacement of your stock shock absorbers.

Also showcased was our line of 4X4 Dampers. We have a total of four offerings- Sports, Gravel, Premium, and Rally. To date, TEIN Japan has already launched the Premium line, with applications for the Mercedes G63 AMG and Nissan Patrol (these are for the Middle East market consumers). 4X4 Rally dampers are a made-to-order application, which we’ve catered to competitors in rally raids and such. I’m personally interested in the Sports line, and I think that would be a great offering for the North American market!

TAS 2016 (iPad Pictures) 041 blog

TAS 2016 (iPad Pictures) 026 blog

TAS 2016 (iPad Pictures) 025 blog

TAS 2016 (iPad Pictures) 024 blog

Our EDFC ACTIVE PRO display also got a lot of visitors. It’s a unique offering in aftermarket suspension. There’s no other unit out there that gives you the option of having dynamic suspension tuning on the fly like our ACTIVE PRO controller!

TAS 2016 (iPad Pictures) 019 blog

Our Hydraulic Bump Stop (H.B.S.) display intrigued a few visitors, as they weren’t sure what it was or how it worked. We had a tester for them to try out, as well as some clear models for them to see the inner workings of our H.B.S. system!

TAS 2016 (iPad Pictures) 048 blog

While we were there, we had a chance to walk around and see what else is new among other manufacturers. We even visited our friends at Defi! Here’s their upcoming release, the new Sports Display F unit!

Tokyo Auto Salon (Jan 17, 2016) 030 blog Tokyo Auto Salon (Jan 17, 2016) 028 blog

Here are some other things we got to see!

Tokyo Auto Salon (Jan 17, 2016) 157 blog Tokyo Auto Salon (Jan 17, 2016) 147 blog Tokyo Auto Salon (Jan 17, 2016) 136 blog Tokyo Auto Salon (Jan 17, 2016) 132 blog Tokyo Auto Salon (Jan 17, 2016) 128 blog Tokyo Auto Salon (Jan 17, 2016) 124 blog Tokyo Auto Salon (Jan 17, 2016) 120 blog Tokyo Auto Salon (Jan 17, 2016) 111 blog Tokyo Auto Salon (Jan 17, 2016) 106 blog Tokyo Auto Salon (Jan 17, 2016) 105 blog Tokyo Auto Salon (Jan 17, 2016) 163 blog Tokyo Auto Salon (Jan 17, 2016) 042 blog Tokyo Auto Salon (Jan 17, 2016) 024 blog Tokyo Auto Salon (Jan 17, 2016) 007 blog

That was a wonderful experience for our U.S. staff, and we certainly look forward to representing the U.S. at next year’s Tokyo Auto Salon!

TEIN Staff TAS 2016 blog