Global Time Attack’s Super Lap Battle 2016

This week is the Super Lap Battle Time Attack event at Buttonwillow Raceway Park, hosted by Global Time Attack.

Damn, that’s a mouthful to say…

Anyhow, we’ve continued to attend the event for the past 6 consecutive years now. Our main purpose is to check out how the event goes, see how it has grown, and also to assist any teams/drivers that are using TEIN suspension.

For the most part, most teams/drivers are pretty experienced with their setup. So it’s not like we’re trying to rearrange everything they’ve setup and working for them. We just want to see how we can extract a bit more performance with a little bit of tuning. We bring one of our in-house engineers to speak with the driver and get feedback on how the car feels. From that, we are able to make an assessment on whether any changes to the suspension should be made, or if some other aspect should be altered. Funny enough, tire pressures tend to be overlooked.

The past few years has really just left us looking like spectators, however. Again, most of the teams have their race cars sorted out. So there isn’t much for us to do except check out the progress of each session.

For this year, we really only know of two teams on TEIN-equipped cars competing. Evasive Motorsports is bringing their R35 GT-R to run in the Unlimited AWD class, and Sport Car Motion (SCM) has their DC2 Type R Integra in the Limited FWD class. Both teams using our Super Racing damper kits.

scm-itr

The SCM Type R has proven to be plenty fast, mainly because they know how to extract the most out of their Rotrex-charged K24 engine setup. [Not] oddly enough, their Super Racing dampers are completely off-the-shelf. No changes in valving, and spring rates are per our recommendation. We did a refresh on the dampers last year, but unfortunately the car couldn’t make the event. Considering this specific Super Racing kit was on the team’s previous EG Civic race car, and that it has just over 6 years of use, the dampers were due for a rebuild anyway. We look forward to seeing the Type R run again this week!

 

evs-gtr

Evasive Motorsports has only taken their GT-R, in its current iteration, to a couple of track days. Back when the car had the very basics (our Super Racing dampers, racing brake pads, upgraded wheels & tires), they were using our recommended setup. Now, with a slightly wider body and more aero additions, we’ve uprated their springs. Other than that, the Super Racing dampers have our 3-way units installed, but valving has been kept as out-of-the-box. Wheels are a bit larger now, and they’re using a much more sticky tire. On its maiden voyage in this setup at Buttonwillow, the car did something in the neighborhood of a 1:47.00 lap time. No time spent trying to fine tune anything, and that’s what they run……… Damn. We weren’t expecting something that quick for what is essentially a still very street-bound car with full interior, full amenities. While we would love to attribute this shockingly fast time to our dampers, the fact is that Evasive Motorsports aren’t any slouches when it comes to building a proper car for the track. We’ll see what else the team does to knock down a couple more seconds from the timer.

Other than those two cars, which would keep our engineer busy enough, we’ve yet to hear of anyone else that may need our assistance. But, as I mentioned, they probably don’t need our help……

 

……….. You know what,,,,, this is just starting to sound like an excuse for us to just go and watch some racing! Don’t tell my boss…

 

 

New Video of Evasive Motorsports’ Nissan GT-R!

We never really get bored of the project vehicles that Evasive Motorsports works on every year, even if it’s a project we’re not directly involved with. GT Channel, in collaboration with Nitto Tire, put out a new video showcasing Evasive Motorsports’ Nissan GT-R, the very same car that was displayed at our SEMA booth last year.

Progress on this car is relatively slow. However, as you can see in everything Evasive Motorsports creates, these are all well-thought modifications. Rather than jumble a bunch of parts to create a race car, the team at Evasive tests each and every component in a long-winded effort to extract the absolute highest performance they can. It’s a balancing act, and an act they know very well.

For several years now we’ve been very fortunate to not only have Evasive Motorsports as one of our customers, but also as one of our largest promoters for our products. That’s not to say that they are necessarily brand exclusive. They also do builds using suspension components from various manufacturers. We were glad that they approached us when it came to their project GT-R.

There is already a plethora of suspension components available for the GT-R, none of them really being all that cheap. And if we’re being honest, neither are our coilover kits. The GT-R, from the factory, already comes with a great suspension setup. It takes time to R&D a kit that can really improve the vehicle’s performance. To date, we’ve released our MONO SPORT coilovers and our SUPER RACING coilovers. Evasive Motorsports chose the latter, opting for the SUPER RACING dampers’ separate compression & rebound adjustment, as well as aluminum bodied dampers. Available as an option through our Overhaul & Revalve service is our 3-way unit, giving our SUPER RACING Dampers both low and high-speed tuning abilities for compression.

We’re working closely with Evasive Motorsports as they dial in their suspension for the GT-R. Again, it’s a process, and any major changes to the vehicle, whether additional power, or additional aerodynamics, or even more grip, directly affects how the suspension reacts. We want to make sure they get the most out of our suspension. Also, they’re perfecting their suspension setup using our EDFC ACTIVE PRO system! That certainly makes for a very adaptive suspension package!

Anyway, we’ve delayed you long enough getting you to the video. Check it out below!

 

MotoIQ’s Top 13 Tuner Cars of SEMA

Once again we’re proud to see some TEIN equipped vehicles to make MotoIQ’s list of top tuner cars of SEMA 2015! One of them, Evasive Motorsports’ Nissan GT-R, happened to be our booth car for the show (OH, DID YOU KNOW THAT ALREADY?! ;)). That’s definitely something for us to be proud of! Evasive’s GT-R uses our Super Racing dampers (which also has our 3-way unit for low-speed and high-speed compression adjustment) and EDFC ACTIVE PRO.

Another vehicle to make the list was Whiteline USA’s Scion FR-S owned by Jonathan Polidano, Technical Sales Manager for Whiteline USA. He’s using our MONOSPORT dampers and EDFC ACTIVE PRO.

While we took no part in physically building these two cars, we are honored to have our engineered suspension grace these builds. Evasive Motorsports plans to use the car for local Time Attack events in California (and possible out of state events), while Jonathan Polidano plans to use his FR-S for NASA series events. Make no mistake, neither of these cars were meant to be show cars!

Congrats to Evasive Motorsports and Whiteline USA! We’re certainly glad to be a part of your beautiful cars!!!

top-ten-nissans-at-sema-2015-evasive-motorspots-time-attack-gtr

polidano frs

 

TEIN Equipped Cars of SEMA 2015

Each year we are very fortunate to be able to attend SEMA (either as an exhibitor or a visitor). We always look forward to seeing all the great aftermarket parts so many manufacturers are putting out, and we also always look forward to the vehicle builds that manufacturers and individuals bring to Las Vegas. Each and every year we attend we get to see some of these cars using TEIN, and that makes us very proud. It is truly an honor to have our suspensions grace some of the most beautiful builds!!!

This year, we had the opportunity to assist with several builds. Starting with:

Evasive Motorsports’ Nissan GT-R:

This is actually a vehicle we have had on TEIN Super Racing since last year (it was in the Volk Racing/Rays Wheels booth for 2014 SEMA). This year, we wanted to showcase our Super Racing dampers with the new 3-way Unit (for low and high-speed compression adjustment). However, for 2016, we will convert back to 2-way as Evasive rebuilds the car for Time Attack Duties (as part of their class requirement).

top-ten-nissans-at-sema-2015-evasive-motorspots-time-attack-gtr

 

Mackin Industries/ Project Mu Nissan 204SX:
Brian and Julia Duong of Mackin Industries built their 240SX for Project Mu. Unlike other 240SX’s, this one is not all hacked up and fitted with some crazy widebody. That is a large part of this car’s appeal- just how clean the body looks and with just some simple modifications! Looks great with our STREET FLEX damper kit.

top-ten-nissans-at-sema-2015-project-mu-240sx

 

Evasive Motorsports’ 997 Porsche GT3:

This vehicle is using our custom Specialized Dampers made through TEIN Japan. We hope to do more testing on this platform soon and bring the kit to market!

evasive 997

Nissan GT-R Nismo:

This was in Mackin Industries/Rays Wheels booth for SEMA. Very tastefully done and using our MONO SPORT suspension.

SEMA 2015 (Pauls iPhone) 003 resized

Whiteline’s Toyota FR-S:

Owner Jonathan Polidano took his personal FR-S and made it into Whiteline’s occassional track car. Using our MONO SPORT dampers with EDFC Active Pro.

whiteline zn6
X-Force Exhausts Ford Mustang GT:

This 2015 Mustang GT is currently on our prototype set of S.Tech lowering springs. Sitting on 20″ Volk G25’s, this has the perfect stance!

x force s550

 

Lexus GS-F:

Built by Gordon Ting, this brand new Lexus GS-F is on a prototype set of our STREET ADVANCE coilovers. Another tastefully modded car still incorporating most the the car’s natural body lines.

lexus gs-f

Evasive Motorsports’ Evasive-Spec S2000 Ver.3:

A customer car that was just freshly built from the ground up and using Evasive Motorsports’ very own Evasive-Spec Super Racing dampers. Such a beautifully executed build. Nothing spared, everything to the highest quality!

Evasive S2K resize

DC Sports Subaru WRX:

Using our newest FLEX Z dampers and paired to our EDFC ACTIVE PRO setup, this simply prepared WRX looks good and has the performance to match its appearance!

dc vaf

Toyota RAV-4 Rally Car:

And let’s not forget the Rally RAV-4 of Ryan Millen! This was sitting across from the TEIN booth. We love it in all its dirt and splendor! Using a customized set of our Group N dampers.

rally rav4

It was a great SEMA for us, and one that had TEIN’s presence wherever we walked! Glad to be a part of so many great cars!!! We hope to be just as prevalent for next year’s SEMA, if not more so!!!

 

Formula Drift Rd. 7 (Irwindale Speedway)

We’ve been attending all the California Formula Drift events for the past few years now. This year we decided to attend all U.S. events. While quiet on our blog about this, we’ve kept followers up to date on our Facebook and Instagram feed (@teinusa). So of course we’re looking to go to the final event for the 2015 season!

Irwindale-Speedway-closes-its-doors

An old-school picture of the Irwindale Speedway, probably in its prime and definitely well before drifting ever became a thought.

As we understand it, and as it has been a threat looming over this particular event, this may be the last Formula Drift event at Irwindale Speedway, as the current owners/investors have plans to bulldoze the facility and track and make way for a,,,,,,,,, shopping center?

 

Kinda BS if you ask me. Anyway, if this is true, we hope the race will truly be a memorable one. This season’s Formula Drift was full of unexpected turns (semi-pun intended??), and almost every event has had its own controversial matter. We’re almost guaranteed a big bang finale.

In terms of exposure in the drifting scene, TEIN has been relatively quiet. There are two cars out there using our suspension, but we’re not inclined to say who. Last season, we had Geoff Stoneback on board with TEIN, but for 2015, being his first year full-time in the Pro class (was Pro 2 last year), he was picked up by another sponsor. To be honest, we’re quite proud of that. It goes to show that Geoff is truly a talented driver, and now he has the backing of quite a few sponsors! We know he’ll only be doing bigger and better things for years to come! Fortunately we keep in touch with him, and he’s kind enough to pay us a visit at the TEIN booth for every event so far! Truly a great friend of ours!

Go Geoff!!!

Go Geoff!!!

Anyway, like always, we’ll be there and will have TEIN goods on hand. So stop by and say hi! We’ll also have our good friend Reginald Cunanan and his beautiful Mitsubishi Evo X on hand.

Reginald CZ4A blog 6

Rd. 7 for Formula Drift is on October 9-10, 2015! Get your tickets at the Formula Drift Webpage

 

First Set of Evasive-Spec SRC w/ 3-Way

Our friends at Evasive Motorsports have a date at the race track later this year. And while their S2000 is still in pieces, starting to be reassembled, they had sent in their very own Evasive-Spec Super Racing (SRC) coilovers for a rebuild.

But wait, there’s more!!!

They got wind of our new 3-Way units designed specifically for our Super Racing coilovers. They figured since they’re going all out on this S2000 this year, they wanted to upgrade their SRC’s to get the most out of it. Of course, we still needed to test it. Just having received the units a few months ago, we have now been able to start work on them.

We just recently posted about the 3-way units and their benefits. This car is going to Buttonwillow for the end of the year event- Global Time Attack’s Super Lap Battle. This is a great venue, and the course has plenty of challenges. It’s also less than perfect, with plenty of rough surface transitions, bumps, curbs, etc. This is an grueling test for both driver and machine, and this easily this makes Evasive’s S2000 a great candidate for the 3-way modification.

SRC 3-Way OH 001

To make a long story short, we said “OK” then they said “Cool”, and we were like “Awesome”.  After several rounds of back and forth acknowledgement, we got to work.

While we do not have details on the cost of the units and revalve service just yet, Evasive shelled out some [MAJOR] ducats and got them installed while we refreshed their dampers.

A simple glance at the coilovers wouldn’t reveal a whole lot. The 3-way unit itself is adapted directly to the External Reservoir, but it looks different (noticeably larger) than the Base Valve adapter it replaces.

EVS SRC with 3-Way (assembled) 015 resize

A Front and Rear SRC side by side.

 

Also, the SRC dampers still maintain EDFC series compatibility. It is just that it only works for Rebound and Low-Speed Compression. High-Speed Compression will be left as a manually adjusted setup.

EVS SRC with 3-Way (assembled) 025 resize

Front damper with EDFC Motor on Compression (External Reservoir) and Rebound (Top of piston shaft).

EVS SRC with 3-Way (assembled) 022 resize

 

EVS SRC with 3-Way (assembled) 020 resize

Rear damper with EDFC Motor installed on compression and rebound.

We’ll try to get you guys some updates on this as Evasive’s project car nears completion. They have a test day planned, which I’m sure they’ll document. We’re looking forward to getting these units fully evaluated by them!

3-Way Damper Customization for Super Racing Suspension

This has been a long time coming. We’ve actually had 3-way damping (Rebound, Low-Speed Compression, & High-Speed Compression) technology for a long while now, made for our N1 suspension. But, it is very expensive and mainly reserved for race teams only. We also developed one for our Gr.N and 4×4 dampers, which are much more robust units, but these offered a wider range of tuning possibilities due to rally suspension needing the highest available tunability because of the higher piston speed range these dampers have. As you can imagine, this was an even more expensive unit.

4x4 damper

Here’s a 4×4 Damper with 3-Way Unit installed on the External Reservoir.

 

4x4 3 way

As you can see, the 3-Way Unit for our 4×4 Damper doesn’t look much different than the newer units we’ve just come out with. That’s because the new ones are nearly a direct derivative of the 4×4 Damper (and Gr.N) units, just much more affordable in terms of manufacturing cost. The technology, which is proprietary, is just about the same.

Now, we’ve developed a much more affordable (in comparison to the original units), less complex, and effective unit based around the Gr.N 3-way unit’s design that we will start doing testing on very soon!

SRC 3-Way OH 001

The 3-Way Unit (Silver) is made as an adaptive system to our Super Racing coilovers. We replace the original ADJ System, as we refer to it (or Compression Adjuster, if it’s easier) with our 3-Way Adjuster Unit. As you can see, we have two different designs depending on how we mount the external reservoir.

What’s so special about 3-Way damping? Well, this specifically affects the compression side of damping. The thing is, while we can easily tune a damper for what we believe to be the most ideal conditions, race cars see various changes in track surfaces that can affect their elapsed time. Race tracks can be a mix of glass-smooth surfaces followed by huge bumps or kerbs, and even expansion joints, or just rough surface transitions. This can unsettle a car quickly, and the less time on the throttle means seconds being added to the elapsed time.

Such surface transitions require a damper that responds to such instances by allowing the compression side to actually soften for a brief moment. If you think of it from your car’s tires’ aspect, an increase in damping force as piston speed increases can cause the tire to momentarily lose contact with the surface (hop). That means a loss in traction. Remember, a car maintains its best mechanical grip when all four tires maintain contact with the surface it rolls on, and that means the driver can keep on the throttle for a longer duration.

Many of you may have heard of “Digressive Valving” for dampers. What this means is that as damper piston speeds increase, the damping force has actually decreased (instead of increasing exponentially as this speed increases). Many dampers, by design, are technically digressive valving. However, the drop off in damping force may not be as much as some manufacturers are expecting. So, some may use some type of blow-off valve that opens extra ports as piston speeds increase instead of just relying on the shim stack assembly, and this creates a greater drop off in damping force as piston speed exceeds a certain level.

Low-speed, both in terms of vehicle speed and damping speed, is easier to control. There is very little resistance to the tires contact with the road surface. It is when vehicle speed or surface changes occur that mechanical grip becomes more of a concern.

To correct for such instances, race dampers have some form of high-speed damping control, and mainly on the compression side. This is where our new 3-way unit comes into play.

As mentioned before, we have already had versions of this, the most popular being on our Gr.N coilovers for rally. Think about the road surfaces that rally racing has- loose gravel, gaps, jumps. These are all things that can make a tire lose contact with the surface quickly. We’ve done really well with our 2-way adjustable Super Racing dampers, but as race cars get faster and faster, their suspension needs to cope with potential road surface transitions and react at a much quicker rate. We’ve been trying to get a 3-way version of the Super Racing dampers out to market, but it was just too expensive with our previous technology. So, we now hope to have something a bit more reasonable! However, we’ll only offer this as an upgrade under our overhaul service.

Also, if you’ve ever heard people talking about unsprung mass (weight not being supported by the suspension under gravity) as a concern, it is because heavy unsprung mass (tires, wheels, brakes, knuckle/hub, etc) can cause great upward deflection momentum, and that means a tire can lose contact with the road surface for much longer (in terms of fractions of a second). While we can try to combat that upward momentum by increasing spring rate (to try and speed up rebound force), it doesn’t benefit the compression side. In fact, this only exacerbates the problem with lost traction. What we want is a damper that has the ability to control a wider range of compression speeds. This will help keep the tires in traction, or as some people say- keeps the car planted.
For now we have only developed them as optional units for our Super Racing setup, and we’ll have one of our closest sponsored parties using them for this year’s Global Time Attack Super Lap Battle finale for the 2015 season. The racetrack, Buttonwillow Raceway Park, is a great test for us as the road surface has all sorts of transitions and undulations that can really hamper a vehicle’s ability to be fast.

SRC 3-Way OH 005

SRC 3-Way (EVS) 007 resize

SRC 3-Way (EVS) 010 resize

This 3-Way Unit is specifically for our “SA” type dampers, or dampers for double wishbone or multilink suspension. Basically it is directly mounted to the damper body.

 

SRC 3-Way (EVS) 014 resize

SRC 3-Way (EVS) 015 resize

For our Strut Type suspension (Inverted monotube design), or where room doesn’t allow us to mount the external reservoir and 3-Way Unit directly to the damper body, we can do a remote setup, this give us some flexibility in mounting the external reservoir/3-Way Unit to the vehicle. As much as possible, though, we try to keep the remote hose as short as possible.

Stay tuned for more updates on our 3-Way testing.

Our In-House Engineer’s personal Scion FR-S

While most of us are pretty much desk jockeys here at TEIN USA (just kidding!), some of our staff enjoy spending their free time at the local race track. Local to us southern Californians is something like a 1 hour drive on average.

One such racing enthusiast is our very own in-house engineer, Shuichiro (a.k.a.- “GQ”). He occasionally takes one of his daily drivers to the track. He’s currently driving his 2013 Scion FR-S. Prior to this, he had a well-prepared Honda S2000. However, there was one occassion where he tried to get all environmentally friendly and drive a Toyota Prius. Dunno what he was trying to do there. He was probably all like “I wanna be like Brad Pitt” or something. Don’t get me wrong, he’s still a true race enthusiast. That hybrid car stuff was just a phase we’re trying to forget about…

He was told to "look natural". This is his idea of "natural". So GQ.

He was told to “look natural”. This is his idea of “natural”. So GQ.

But yes, he’s an enthusiasts. Whenever he has the chance, he’ll prepare his car for track duty. Being that he works at TEIN, that means he has access to any one of our suspension kits.

We are actually making his car our guinea pig for damper development, for both new product and experimental damper valving. Since it is easier to do so with our 2-way adjustable setups, we have him run our Super Racing coilover. Not a bad hookup for making him our crash test dummy! I mean, test driver. In the name of science!!!

The current build sheet for his FR-S is as follows:

*Exterior
Front lip spoiler: Revolution
Side skirt: Downforce Evasive (exclusive model)
GT wing: Voltex Type1S
Duck bill: Five Axis
Fender Spoiler: TRD

*Interior
Seat: Recaro SP-G
Harness: TAKATA Race 4

*Footwork
Coilover: TEIN SRC (Ft9kg/Rr10kg)
Wheel: Advan GT 18×9.5 +40
Brakes: AP Racing front big brake kit w/ 6 piston calipers
Brake pads: Project Mu

*Drive train
LSD: ATS&Across

*Engine
Intake: Revolution
Throttle Body: Revolution
Exhaust manifold: Fujitsubo SuperEX
Front pipe: Berk
Cat back: Fujitsubo Authorize R Type S (w/ burnt tip)
Oil cooler: Greddy
ECU: Ecutek

A very simple build. Nothing too over-the-top, and definitely a good platform for us to continue damper development on. In fact, the FR-S/BRZ has been one of the best selling of new vehicle platforms for us in terms of suspension sales!

shu bw

So, if you see him at events, especially around Buttonwillow, don’t hesitate to say hi to him. Better yet, prepare a bunch of technical questions to ask him in case you run into him! He loves that kind of stuff. Apparently.

Wheel Fitment Complaint

It seems as though lately we’ve been having a high increase in complaints from consumers about tire rubbing.
Now this rubbing encountered is not necessarily coming from the original OE wheel and tires but rather aftermarket wheel and tire set ups.

Wheel Fitment 6

Wheel Fitment 4

 

 

With this in mind a common sense factor should be taken into consideration but is always thrown out the window as the car must look sweet with an aggressive offset. Bear in mind that not just any wheel and tire set up can be used on any vehicles.

Wheel Fitment 2

Many consumers that do achieve the desired fitment would also require further modifications to the wheel well and other suspension components. The rubbing has nothing to do with the lowering spring or coilover set up as it never was any type of issue upon the initial testing of the vehicle with the OE wheels. Now the lowering spring or coilover set up may not be to the consumers expectations, either allowing for too much travel when weight is placed on a particular corner of the vehicle causing the rubbing, or not enough to bring the wheel and fender clearance to the desired place.

Wheel Fitment 3

I, too, have ran across this dilemma thinking that the wheel and tire set up would be sufficient enough for the drop I was looking to maintain. With the same issue encountered, rather than blame others for my error, I decided to make further modifications as to allow for the fitment. Let’s just say that it still encountered rubbing at full suspension compression but worked well enough for me.

So, before you decide to lower your vehicle and get new wheels, consider certain factors such as wheel size (diameter, width, and offset) as well as tire size (width and outside diameter). These factors can affect overall wheel fitment and can cause problems with rubbing if not taken into consideration.

***Images shown above were those found on google search and I do not take any type of claim to them being images of my own.***

Super Lap Battle by Global Time Attack Results

We’re glad to see some of our friends back at it at this past Friday’s Super Lap Battle by Global Time Attack, which took place at Buttonwillow Raceway Park!

As far as TEIN-equipped cars go, we had Sportcar Motion’s Acura Integra Type R on Super Racing dampers, which ran a 1:52.886 just last year. We also had Pradana “Ping” Wilianto’s Acura CSX on our Mono Flex dampers, who had ran a 2:01.314 last year, and Bobby Lane Racing’s Honda Accord on Mono Flex dampers (1:59.158 last year).

During the off-season, if there even is one, we hadn’t received any special requests from these guys. Normally, we’ll at least get a damper refresh/rebuild request. Instead, they all focused on a few other modifications to get their car ready for this year’s event. With the exception of Sportcar Motion, who hadn’t really touched their Type R since last year except to rebuild their transmission and try a different rear diffuser.  They are using a different tire for this year, however.

Anyway, it was still an event for us to attend with our in-house engineer, in hopes that we could provide some trackside support to these guys and any other teams/drivers using TEIN dampers.

Just like previous years, we ended up just looking like the Maytag repair man with nothing to do except take notes on each vehicles suspension setup.

We were absolutely impressed with each teams performance. Their results are as follows:

 

Sportcar Motion’s Integra Type R (Limited FF class)- 1:51.916

2nd Place Finish!

Super Lap Battle (Buttonwillow) Nov 2014 041 (Custom)

 

Pradana “Ping” Wilianto’s Acura CSX (Street FF class)- 1:59.639

2nd Place Finish!

Super Lap Battle (Buttonwillow) Nov 2014 021 (Custom)

Bobby Lane Racing’s Honda Accord Limited FF class)- 1:55.241

3rd Place Finish (behind Sportcar Motion’s Integra)!

Super Lap Battle (Buttonwillow) Nov 2014 057 (Custom)

 

Each achieved personal best times, which was great news! As you can expect from their placement in their respective class, competition was stiff. In Limited FF, Point Zero Autosound and Performance trucked their Acura RSX all the way from Ontario Canada for this event! They finished in 1st place with a 1:51.789! Just a narrow margin between first and second place!

Super Lap Battle (Buttonwillow) Nov 2014 010 (Custom)

*We must note that the Sportcar Motion looked to be on pace for an even better time. But, on the last stint out on track, a brake failure caused the Integra to spin. Fortunately, driver Tim Kuo was able to recover from the spin without any further damage to the car. However, the damage to the brakes was all that was needed to prevent another fast lap.

Super Lap Battle (Buttonwillow) Nov 2014 047 (Custom)

Pradana “Ping” Wilianto had one goal in mind- a sub 2 minute lap. Why? He’s one of the few Street FF cars that is a legitimate street car. He retains full interior and air conditioning (you gotta maintain some amenities on the track!). Last year, he was under Enthusiast FF with a 2:01. Now under the Street FF class, he clocks in a 1:59, and not much else has changed to his CSX’s setup!

Super Lap Battle (Buttonwillow) Nov 2014 001 (Custom)

Bobby Lane Racing also kept their car relatively the same. Last year, we revalved for much stiffer springs to compliment their new aero package.  A 1:59 was a very respectable time last year. This year’s 1:55 is even more impressive!

Super Lap Battle (Buttonwillow) Nov 2014 054 (Custom)

Overall, we’re very happy for these guys. Of course, we’re impressed with the out-of-the-box performance our Super Racing set for Sportcar Motion’s Integra and Mono Flex set for Ping’s CSX did. But, it always comes down to overall vehicle preparation, which each of these guys did a stellar job at! We won’t be satisfied until they stand atop the highest podium. So you can bet we’ll do what we can to get them there next year!

It was also great to see some of our other friends, such as Evasive Motorsports Scion FR-S and Will Wattanawongkiri and his S13 at the event. Unfortunately for Will, mechanical issues plagued him from staying in competition.

Super Lap Battle (Buttonwillow) Evasive FRS (Custom)

Super Lap Battle (Buttonwillow) WWR S13 (Custom)

We also fancied the Spoon Sports Civic Type R being piloted by Dai Yoshihara! Ran a super quick 1:48 in Unlimited FF!!!

Super Lap Battle (Buttonwillow) Spoon CTR (Custom)

And this year’s overall winner- GST Motorsports’ GC8 piloted by Jeff Westphal! 1:38!!!!! Whoa

Super Lap Battle (Buttonwillow) GST GC8 (Custom)