Bump Stop Trimming

Posted on September 25, 2015 by Paul P.

Without a doubt lowering springs is easily one of our biggest sellers. It’s a simple upgrade for someone wanting to lower their vehicle but not wanting to really sacrifice much in the way of ride quality, and it’s also much more affordable than a coilover kit. This is an especially common upgrade for people with newer vehicles, or cars still under warranty (or maybe they don’t have much to spend since they just got a new car).

As many of you may know, we make our lowering springs compatible with factory (OEM) dampers. Not necessarily in just fitment, but also in spring rate. Our lowering springs are not very aggressive. If you take a look at our lowering springs’ specifications for your vehicle, you may see that the ride height drop is not too aggressive (maybe better than some other manufacturers). Some other applications of our lowering springs may seem to be very aggressive. It’s all a matter of how much room we have to play with when designing our lowering springs.

Most important for customers is reducing the tire to fender gap. As of the past few years, the request is for a “flush” fitment, where the tire just closes up the gap with the top of the fender opening. As much as possible, we want to create that type of fitment for the customers, even making a staggered ride height drop for front and rear to achieve a nice and even wheel gap. But, where we reach limitations is the factory damper stroke length.

Some factory suspensions have very limited stroke length, and this makes it increasingly difficult to design a spring that will aggressively lower a vehicle. That isn’t the only limitation. We look at clearance with the fender, within the wheel well, as well as how it may affect steering/suspension geometry. We always design our lowering springs to give you the most ride height drop in as safe a level as possible.

So, in regards to trimming bump stops- why is this important? If we find that aspects, other than damper stroke length, seem to be very generous, we know that we can make a lowering spring that will work with a shortened bump stop. So we include a chart by vehicle application that shows how much you will need to trim for front and rear when installing our lowering springs.

Some cases may require a different type of trimming style for the bump stop. Typically it is just trimming the bottom portion of bump stop and retaining the top piece (A Type). Sometimes it’s the reverse (B Type). In other cases, you may need to trim a middle section and retain the top and bottom piece (C or D Type). See below the different style cuts we recommend, depending on the vehicle:

We know several customers skip the bump stop trimming step. This can cause several issues. We’ve added this measure so that you can retain a bit more stroke length at the newly lowered ride height. This also helps improve ride quality. Because the bump stop is made of a high durometer polyurethane material, it is like a secondary spring, but a really stiff secondary spring. Since the dampers are not valved to handle such a stiff secondary spring, it can make rebound feel really harsh. Some may say bouncy. Constantly hitting the bump stop can cause the damper to prematurely wear or potentially blow out, too.

Bump Stops come in all sorts of goofy shapes. Mind you, these were engineered with a specific design.

The bump stop itself is a really lightweight piece, but it is of a high durometer and takes a lot of force to compress. At least it is easy to cut into.

Fortunately, you can cut easily into the bump stop using a box cutter/safety blade. It slices pretty easily.

Here’s a picture of a 2015 Camry bump stop. This is a more typical design that we see- top is a larger outside diameter and tapers, with billows that make it easier to determine which section we recommend trimming.

Using a safety blade, we’re able to cut a bottom portion of the Camry’s bump stop. We’ll be retaining the larger piece on the left and reinstalling onto the front strut.

This bump stop uses some plastic ring, likely to control the bump stop’s compression. In our case, we need to trim a middle section.

We cut this into three pieces, and the middle piece will be removed. The remaining top (left) and bottom piece (right) will be reassembled on to the damper.

So, while you will have your suspension taken a part for a little while when installing our springs, take the time to see if your bump stops will need to be trimmed. Check the included instructions with our lowering springs to find out that info.

Specialized Lowering Springs?

Posted on September 23, 2015 by Paul P.

We rant on and on about our ability to make custom damper kits for vehicles, especially vehicles that no longer have any aftermarket support. This program is the easiest way to get a custom set of suspension made for an otherwise obsolete vehicle.

What we fail to really mention is that we have the ability to do custom springs. Actually, we take that back- we have mentioned that, because some kits don’t allow the use of a ride height adjustable setup. For vehicles that utilize a spring separate of the damper, we custom wind springs specifically for that application. So, there you go! We can make custom springs for you!

We recently did a set for Toyota. While we cannot cough up the details just yet (I’m sure you can figure it out if you search hard enough within this post 😉 ), we’ll just say it is for a platform we don’t already have product available for. And actually, they weren’t looking to do much to this car. The request was a set of lowering springs that would give the car a 1″ drop front and rear.

And here they are:

If you’re thinking “What the hell is an Eibach spring doing in a TEIN blog post?”, well then that’s a burn. This red color was at their request. That’s fine by us. We can basically do custom colors anyway. So if they want red springs, red springs it is!!!
We must mention that custom springs are not cheap. A set of four coil springs go for $700 retail. Ay yi yi!!! However, if this is something that may lead to a person wanting to do a private line of springs through us, the cost (which includes a development fee) will basically be covered on the first spring order. Not uncommon, as we’ve done that before, especially with our coilover kits.

We can also do remanufactured springs (springs of an older/discontinued line). Those start at $560 retail for a set of four.

The only types of springs we do not manufacture are torsion beams/bars or leaf springs.

So, if you have a need for custom coil springs, give us a ring. We can definitely help you out!!!

“Yeah, I’ve got a set of TEIN Coils”

Posted on September 15, 2015 by Paul P.

Whenever we hear that (blog title), we tend to understand that a customer has a set of our lowering springs. However, for some strange reason, people online or that call us are referring to our suspension kits as coils, whether it be a complete suspension kit like a STREET FLEX or STREET BASIS, even a SUPER RACING setup.

We must ask- WHY ARE YOU REFERRING TO THEM AS “COILS”?!

We’re just as guilty, using different terminology than what some people may understand. For example, saying “coilover” implies simply that- a coil over a damper. This is how most people know of our product since our height adjustable setups are typically coilover, but is this a coilover?:

STREET FLEX for 2003-2009 Nissan 350Z

As pictured above, this “coilover” kit uses our Height Adjust System (H.A.S.) for the rear, as pictured on the left. So it is in fact not a “coilover” with exception of the fronts (pictured on the right). We’re wrong for ever referring to such kits as a coilover package. Instead, this is a suspension kit. But, for simplicity’s sake, and in acknowledging what are customers know us for, we continue to call them coilovers. It’s easy, and it won’t confuse our customers.

There are other things/terminology we may use that may be either incorrect to some, or just named differently. For example, the name “Shock Absorber”. It is in fact a “Damper”. Shock Absorber is incorrect because it isn’t absorbing shock. What it is doing is turning kinetic energy (the up and down motion of the vehicle and unsprung mass) and converting it into thermal (heat) energy. Nothing is really being absorbed. It is a transfer of energy from one form to another. However, most people understand them to be Shock Absorbers, so we just roll with it.

And yes, it is “Damper” and not “Dampener”. They may share some similarities in meaning, but they’re in fact used differently. Dampener is typically used to describe a wet or moist condition. But it can also be used to describe a deadening or depressing. Damper, on the other hand, is mainly used to describe a reduction in oscillation or amplitude of force.

We also hear people ask for “Pillar Ball Mounts”, which is easily understood to be (how we know it) Pillowball Mounts. Not a big deal.

Another one that we hear is when people refer to our Seat Locks and Spring Seats (where you can adjust a spring’s setting and vehicle ride height) simply as “rings”. Sometimes we hear them being called “collars”. We use collars, but they are usually much smaller and are used as a spacer in our upper mount assemblies.

That’s another one- upper mounts being referred to as “top hats”. Not really a big deal, and some upper mounts kind of look like top hats. So, [top] hats off to you for using that description!

Willy Wonka wears a Top Hat. He can also be condescending sometimes.

There are some less obvious things that we cannot fault a person for. For example, our inverted dampers for strut type monotube setups, like our older MONO FLEX and our SUPER RACING. People will refer to the shiny part of the damper assembly as the piston or piston shaft. Again, although that is incorrect, we cannot fault the customer for that. Since the damper is inverted, the whole assembly is upside down. The piston shaft is now on the bottom side and inside of the threaded shell case.

MONO FLEX for 2002-2007 Subaru WRX

In the above picture, the shiny rod coming out of the threaded shell case (black) is in fact the damper body and not the piston shaft. The piston shaft is itself inside the threaded shell case and completely out of view.

There’s also the use of the name “Serration Bolts” which we use for the studs in our upper mounts (that secure the upper mount assembly into the strut or shock tower). We realize that confuses a lot of people when they need replacements of these components. Sorry!

The use of “Strut” may also be confusing for some. The above picture of the MONO FLEX for Subaru WRX shows struts, which this chassis of Subaru uses for front and rear. When we say strut, we’re referring to the MacPherson Strut design, which other than being a damper, also serves as a structural member of the suspension by supporting the knuckle assembly. The knuckle assembly comprises of the wheel and brake components. Struts have to be a bit larger in size and be able to handle large side forces/loads.

In comparison, a “SA” type of damper (short for “Shock Absorber”), which is used in Double Wishbone or Multi-link type suspensions, doesn’t have to support such side loads. They are used strictly to control vehicle motion. This is also why we don’t make camber adjustable upper mounts for our SA dampers. It’s position or angle will have no affect on wheel camber.

Can you see the difference between these two suspension designs?

For sure there are other things we hear from customers, but this covers a majority of terminology we hear.

Hopefully that helps break down some of our terminology for suspension components!

TEIN Has Two Manufacturing Plants?!

Posted on March 11, 2015 by Paul P.

That is correct!

Earlier in 2014, we posted about the new TEIN China manufacturing plant, which construction of the plant was completed before the end of the year. This new plant will be focusing on production of our upcoming line of performance replacement dampers. YES, we will finally be working on replacement dampers designed to work with factory springs, as well as our S.TECH & HIGH TECH lowering spring kits! We’ll blog more on this product later.

However, this will not be the first manufacturing project for TEIN China. We’re going to be receiving our new STREET BASIS Z & STREET ADVANCE Z damper lines from the TEIN China plant.

If you had read our previous posts regarding the new “Z” line, you’ll notice that the other Z line of dampers, our FLEX Z coilovers, will be coming from TEIN Japan. Why is that?

TEIN Japan’s Yokohama plant. This new facility was opened in January 2014.

It’s a little difficult to explain. But, in short, TEIN is still a very proud Japanese brand. In fact, many of TEIN’s domestic customer base prefer a Japanese manufactured product, especially more of the high-end kits we offer. So TEIN Japan will still continue to produce some of our higher end product lines, such as the upcoming FLEX Z & FLEX A, MONO SPORT, SUPER DRIFT, HG, SUPER RACING, GROUP N., and several other product lines.

That is not to say there is a lack of pride for the TEIN products coming from the TEIN China plant. In fact, we have invested a lot of money into this new plant in an effort to maintain the same TEIN quality our customers know and expect out of every product. Even machinery and equipment used in TEIN Japan will be the same in the TEIN China plant. A few of TEIN Japan’s engineers and managers will also be making the move to China, not only to train new staff, but to also control all operations. To us, this is a necessary step in controlling and maintaining TEIN quality.

Maybe this would have been a much easier undertaking if we just outsourced manufacturing of these more affordable coilover kits through some other Chinese or Taiwanese manufacturer. Sure, but that isn’t the TEIN way. We’re proud of our technology. Again, we’re not claiming to have invented dampers. We’re just proud to make suspension better through our own engineering and through our own technology.

Still though, why the new factory in China?

Our new TEIN China manufacturing plant!

A very good question. For several years now, we’ve faced stiff competition in the market place, especially with a lot of these somewhat engineered suspension kits selling for well under $1000. We’re not trying to defame any particular brand. So in their best interests, we’ll leave that information out. Sorry! We’re not here to bash on anyone!

It hasn’t been easy for us. For years, most of the feedback from our authorized dealers and wholesalers is how TEIN suspension is overpriced, and no matter how we dissected our manufacturing process in trying to reduce cost, it still didn’t gain the appeal for a broader range of customers. We were essentially becoming a boutique brand. We’re hoping that opening a new overseas facility helps to address this matter. Of course, this exploits a certain factor about manufacturing in China- affordable labor. However, we’re not in China to simply abuse this factor and gain in profitability. It is just a simple fact about the country and its economic structure, and this is how other manufacturers are able to price their products well below ours. This new affordability in manufacturing translates directly into a more affordable product for our customers.

It wasn’t an easy decision. In fact, it was an idea that we never knew would come to fruition. We didn’t simply decide to open up a new plant. We’re talking about a problem that hadn’t been addressed since late 2008, during the dreaded global financial crisis. Again, we could have simply outsourced manufacturing. But, fortunately, we were able to hang on and maintain some profitability over the next few years in an uneasy industry. We had to outweigh every factor before we made this decision to grow. Now, it’s set in stone, and the TEIN China plant is just about fully operational.

Many of TEIN USA’s staff share the same regards as all other U.S. consumers when we hear “Made in China”. It clearly doesn’t have the appeal that “Made in Japan” does. Typically, we view Chinese manufactured goods as essentially NOT GOOD. That was just something most of us grew up hearing and reading about. It’s sad. Then again, think about how many other goods come from China… Why is it that China is commonly associated with terrible quality? I think this is something that TEIN plans to dispel. Being that we’re in control of all aspects of this manufacturing plant, we have the opportunity to change that “Made in China” label. We think that, naturally, Chinese manufacturing can improve.

All TEIN suspension products, whether made in China or made in Japan, will be covered with our manufacturer’s warranty. That won’t change. In fact, we’ll continue to offer after-sales service, such as replacement parts and dampers, as well as overhaul service, to all of our customers so that they can continue to use their TEIN suspension for years and years.

The New, More Affordable STREET BASIS Z & STREET ADVANCE Z Coilovers!!!

Posted on February 18, 2015 by Paul P.

As we had already mentioned, development has started on our FLEX Z coilovers, a more affordable offering of our popular STREET FLEX coilovers. But, we haven’t stopped there with new products for 2015!

At around the same time we start bringing in our FLEX Z coilovers (mid-Spring), we should also have a few applications of our STREET BASIS Z & STREET ADVANCE Z coilovers! However, we’re not too sure the timing, as the new STREET BASIS Z & STREET ADVANCE Z will be coming from our newly established TEIN China plant.

The difference between current STREET BASIS and STREET ADVANCE coilovers from the new “Z” line is that the Z line are non-rebuildable coilovers. Again, this follows in suit to the STREET FLEX -> FLEX Z changes. All other features of the two entry-level coilover lines are the same.

STREET BASIS Z is strictly a ride height adjustable kit. This makes it a perfect setup for the daily driver looking for an increase in handling performance without compromising comfort for everyday use. For many of you considering a lowering spring + performance shock absorber combination, the STREET BASIS Z makes even more sense as we select appropriate spring rates and valve our dampers to match. No guesswork on the end-users part in trying to match one brand of springs to another brand of shock absorbers. The added height adjustment feature allows the end-user the ability to adjust ride height to their preference, something that lowering springs lack. Being that most vehicles are slightly unbalanced from left to right sides, that means you can easily adjust the ride height so that each corner is even from their opposing sides.

STREET ADVANCE Z takes the ride height adjustability of the STREET BASIS Z line and adds 16-way damping adjustment. So, not only do you get a matched spring and damper setting, you now have the ability to tune the dampers to meet your driving conditions. Roads seem a bit rough? Soften up the damping. Glass smooth highways? Crank the damping to a stiffer setting. You get all that and everything in between. STREET ADVANCE Z is also compatible with our EDFC systems (some STREET ADVANCE Z coilover kits may require extension kits for compatibility), giving you a completely adaptable suspension kit based on your driving conditions/characteristics! That’s a feature that not even all sports luxury cars have, and our setup is at a much more affordable price!!!

Like the FLEX Z line, these new STREET BASIS Z & STREET ADVANCE Z coilovers have a very appealing starting price! STREET BASIS Z comes in at $400 while STREET ADVANCE Z comes in at $500!!! Those are unheard of starting prices for a TEIN coilover!

And, just like the FLEX Z coilovers, replacement parts will be made readily available! If your STREET BASIS Z or STREET ADVANCE Z dampers start feeling worn, you can purchase replacement dampers! No need to send them into us for a rebuild since these are fully sealed, non-rebuildable dampers! That will save you some money, and most importantly, extended downtime! We’ll help to get your car back on the road as quickly as possible!

Again, the only major difference is that the new “Z” line of dampers are non-rebuildable.

Internally, we continue to use our ADVANCE NEEDLE for increased per-click damping adjustment. This translates into greater damping change for each click of the 16-way adjuster, making it easier to find the perfect damping setting. Our high performance damper oil, the same kind we use in our race dampers (Gr.N, Super Racing, N1) provides excellent anti-foaming and viscosity characteristics under heavy cyclic rate, giving you repeatable damping feel and performance for the life of the damper.

ADVANCE NEEDLE provides wide-range damping force change per click.

Proprietary damper oil exhibits excellent anti-foaming and viscosity characteristics for stable damping force under extended use.

We will still retain our exclusive damper coatings, too. Our shot blasted, zinc plated high strength STKM13C steel damper bodies are treated to our patented 2-layer/1-bake powdercoating procedure. This gives our dampers excellent protection against corrosion in harsh environments, especially in areas with heavy snowfall. Our patented ZT coating is applied to our threaded adjustment tubes (inside and out), and contribute to smooth height adjustment, and outstanding adhesion to the steel threads. This ZT coating will not peel or flake off even after repeated adjustment. This is due to the ZT coatings’ low friction coefficient. Essentially, it acts as a dry lubricant. That makes every external component of the steel bodied damper completely protected from the unforgiving environments we subject them to, and we expect our dampers to perform at their very best year after year after year…

the bare surface of our dampers are treated to a double shot peening adding surface strength and also prepares it for zinc coating.

We’ve also updated our spring seats and seat locks for increased durability under heavy vehicle loads and smooth height adjustment. Instead of using a rubber spring seat, we’ve added a Delrin thrust washer atop the new, wider spring seats.

Coilover springs will continue to be made from cold-wound SAE 9254 Vanadium alloy. After cold winding and setting, we heat treat the springs prior to grinding end coils to proper dimensions. Before powdercoating, we subject every spring to double shot-peening which aids in increased spring life and fatigue strength. Some coilover applications may have application-specific spring windings and shapes, such as our barrel springs or taper springs.

We will also continue to provide our 1-year warranty against manufacturer’s defects. Even at this new starting price, we will stand behind our products!

So now you’ve got the highest available quality and performance at an extremely low price, and backed with a manufacturers warranty. Unfortunately, we still haven’t made it easier for you to decide with TEIN suspension system you want. So we ask you to please give our sales staff a call at 562-861-9161 for assistance in getting you into the proper TEIN suspension kit for your needs!

FLEX Z Coilover Testing Has Commenced!

Posted on February 10, 2015 by Paul P.

You’ve probably already read our posts about upcoming new products. One, in particular is the new FLEX Z coilover kits which will be here by Spring of this year. We’ve already had a head-start in developing FLEX Z dampers, testing on some of the more popular vehicle applications and working our way down the list, including new vehicles.

I’m sure many of you have questions regarding these dampers, wondering what is so different about it and why we probably have to test.

Well, in short, we’re always testing. Just because a new product may be similar to the items they’re superseding doesn’t mean we should simply copy and remanufacture from an older design. Our products are always evolving. We develop products based on customer feedback and work towards making an even better product.

Here are a few FAQ’s:

How does this FLEX Z coilover kit differ from the current STREET FLEX?

-The only difference is that the new FLEX Z dampers are fully sealed units, rather than the rebuildable setups we make. All other components and features have remained.

Why has TEIN gone with a fully sealed unit?

-The biggest benefit of a fully sealed unit is that we are able to change out a few components that add the the production cost of the coilover kit. We understand that our customers are looking for a more affordable coilover without sacrificing features such as damping force adjustment, height adjustment, and exclusive upper mounts (camber adjustable in some applications).

So, with our fully sealed units, we’re able to cut MSRP down from current iterations of STREET FLEX dampers by nearly $500!!! That’s a massive savings! Starting price for our FLEX Z dampers is $800!!!

Any downsides to a fully sealed unit?

-Obviously that is a great concern for a lot of our customers, especially ones that are already familiar with our overhaul service.

As all of our current coilovers are rebuildable, the customer can send any damper that may have blown a seal, or just needs to be refreshed, and we can do that in-house. We also have the ability to revalve the dampers for different spring rates, should the customer want to match for a specific spring rate in mind. Our engineers have motorsports experience too, so we can work with a customer who has very detailed concerns with damping for specific tracks or driving conditions.

We’re very proud to be able to offer this unique service to our customers, as many suspension manufacturers do not have a damper service option. However, it is not as common a request from our customers. In fact, a majority of the dampers we receive are really for damper revalving and customization, and not just rebuilds. If anything, that serves as a great testament to the durability of our products.

With a fully sealed unit, we cannot open them up again. So, overhaul service will not be available for the FLEX Z line.

So, what happens if one of my FLEX Z dampers blow out? Can I get a replacement?

-You can absolutely get replacement FLEX Z dampers! Contact us for pricing on individual dampers (damper sub assembly), should you ever need one! While we cannot sell direct to the public, we can at least give you this information and even help you find a nearby authorized TEIN dealer that you can purchase replacement parts from. All we will need from you is the part number and lot number from the damper, which is placed on a silver label on the damper itself (label may be placed on lower bracket).

But I was hoping to be able to get a customized set, one with my own valving. Is that still possible?

-Actually yes, it is still possible! You can special order a custom setup for the FLEX Z dampers. It may take some time, since it is coming from Japan (eta is 3-4 months). Since we cannot open the dampers, it will have to be manufactured with another lot. Time frame is dependent on current order/manufacturing schedule. And yes, this does mean that the FLEX Z, as well as FLEX A, coilovers will continue to be made in TEIN Japan’s Yokohama factory.

In fact, if you already have a FLEX Z coilover kit, but are really considering purchasing a specially valved set of dampers, you can just order those specially valved damper sub assemblies separately. Of course, that means you end up with two sets of damper sub assemblies (one out-of-the-box valving, one custom valved). However, that saves you from having to order a complete coilover kit and essentially means you have a back up set of dampers. Mind you, there is still an average ETA of 3-4 months for the custom valved damper units.

Does this all translate to FLEX Z being an inferior product?

-Not at all! In fact, the quality of our dampers has to be even better if we’re going to make a fully sealed unit. That’s our challenge, but we’re very confident in our technology, and we feel that we can provide the same warranty against any manufacturer’s defects with these new FLEX Z dampers! Should you experience any problems with your dampers within the first year of the purchase, send it in to us along with a copy of your receipt from an authorized TEIN dealer and we can take of replacement parts for you, once our claims department has handled all necessary paperwork and questionnaire.

Is the current STREET FLEX better than the FLEX Z?

That isn’t necessarily the case. What we’ve done here is now offer a product to match a customer’s price point. In fact, all of our products are listed in terms of customer budget, as well as features.

Prior to deciding what coilover you want to use, we typically want to find out more information from the customer:

-What is the kit being used for?

-Is this car mainly a street car, occasional track (how often), track only?

-What kind of tracks do you drive on, and can you describe the course and road surface?

-If you are already experiencing any concerns with your current ride quality, please tell us what they are.

-What suspension features do you need?

-What is your budget for new suspension?

Those are just some of the questions we ask. Again, ultimately it is about how much you can spend to get the features you need.

We’re very proud to bring this new product for 2015, and most of all, we’re excited to receive such great responses from customers, especially knowing that TEIN quality and technology can be had at a much more affordable price!

Got questions? Give our sales staff a call at 562-861-9161 for more information!

Not Just Custom Coilovers

Posted on February 7, 2014 by Sergio M.

Our Specialized Damper Program allows for a custom set of coilovers to be made to your specifications, but what about springs? Well springs can also be produced under this program. We have offered coilover systems which utilize a HAS spring for those with a suspension design with a shock spring separate from each other and spring rate changes for those are not available. A custom rate and length set can be produced to your specifications.

IMGP6191s

Even if the application has no product available for it, a custom set of lowering springs can be produced again to you specification. As this is a made to order set, time frames would be around 2 to 3 months for the manufacturing process as well as container freight from Japan. The starting price for a pair of reproduction springs can be anywhere from $350.00 to $450.00. A complete set of custom lowering springs will be around $700.00 to $800.00. Although the price may be a little steep, keep in mind that this would be your own custom one-off set of springs which no other consumer would have.

IMG_4977 (Small)

For further details of this program please feel free to contact us at 562-861-9161 or email tus_sales@tein.com and a friendly staff member will kindly assist you with your inquiry.

2013 Hyundai Genesis Coupe Testing Wrap Up.

Posted on October 29, 2013 by Omar A.

Our R&D department has wrapped up testing on the 2013 Genesis Coupe last month. We are glad to announce that our product line for the Genesis Coupe is compatible from 2010-2013 (see part numbers below). However, 2013 owners will need to purchase the end links for the 2010 model for our coil-over kit for proper function of the factory sway bar.

Below are pictures of the Genesis Coupe. A shout out to Robert from Magnaflow for lending us his vehicle for testing. His Genesis coupe is currently being built for display at the 2013 SEMA show in Las Vegas, NV. as well as local events.

Please reference the part numbers listed below when placing your order. As a reminder always purchase through TEIN authorized dealers ONLY! Also listed below is a link to assist you with locating the nearest Dealer to you.

Part# : GSF12-1UAS2 (Street Basis)

Part# : SKF12-AUB00 (S.Techs)

http://www.tein.com/dealer_list/index.html

FR-S Release Party at Penske Toyota

Posted on June 7, 2012 by Sergio M.

From Left to Right (FR-S First owner. Troy and Young from 5 Axis)

Penske Toyota in Downey, CA had a Release party for the New Scion FR-S and for the First Penske Scion FR-S Owner. We happened to be there since it’s not to far from our warehouse and we have actually been testing the Scion FR-S that 5 Axis let us borrow.

This is the FR-S we have been testing on it looks good on our S-Tech lowering springs that we have been developing for the US models. Ride height drop is approximately -35mm front and -30mm rear, giving the car a great stance, especially with plus-sized wheels.

It was good seeing that not only did they have the FR-S to show, but they had multiple Toyota/ Scion vehicles, some being 5 Axis customers and others being Toyota enthusiasts of new and old. This evening’s event also included a raffle, showroom models of FR-S’s to check out, a DJ, and also some barbecue for attendees.

To date, we have officially release the following parts

S.Tech Lowering springs
lowers -35mm front and -30mm rear
part number SKQ54-AUB00, msrp $280

High Tech lowering springs
lowers -25mm front and -20mm rear
part number SKSA0-G1B00, msrp $310

Type Flex damper kit
preload & height adjustable (-55mm – +5mm front, -45mm – +5mm rear)
damping adjustable (16-way)
Incl. Pillowball upper mounts (camber adjustable front mount)
EDFC Compatible (sold separately)
part number DSQ54-61SS1, msrp $1790

TEIN USA R&D Needs Your Car

Posted on December 13, 2011 by Jonathan L.

TEIN USA’s R&D Section is in need of your car to do testing on.

If you, anyone in your family, one of your friends, or your neighbors owns one of the following cars or any of the cars listed on this page, let them know that TEIN USA needs their car to do testing on.

If your car is chosen to be used for testing you may have your car returned to you with lowering springs or maybe even coilovers free of charge.
The only sacrifice that need be made is your time.
Testing can take anywhere from 3-5 business days.

So let us know by filling in this Test Vehicle Application and one of our staff will be in contact with you.

Remember, we only need one car per testing application, and it’s first come first serve, so apply quickly.

TEIN USA Blog

The latest news and info from TEIN USA

Tag Archives: Springs